A practical reference on Sublimation: what it is, how it behaves, what the literature reports, and where the honest uncertainties sit.
This page was last updated on 2025-08-05 and is reviewed periodically as new material appears.
Lyophilization is a dehydration process that removes water from a frozen material by sublimation under low pressure. The material is first frozen so that water becomes ice; then the surrounding pressure is lowered below the vapor pressure of ice. Heat is applied gently so ice changes directly to vapor without passing through a bulk liquid phase. The vapor is collected on a cold condenser, leaving a dry porous matrix. This process differs from simple evaporation because the material remains frozen during the main drying stage.
The process usually has three stages: freezing, primary drying, and secondary drying. Freezing sets the ice crystal structure and can determine pore size in the final cake. Primary drying removes free ice by sublimation at low pressure and low shelf temperature. Secondary drying removes bound water by raising the shelf temperature, although some water may remain as part of the solid. Cycle parameters depend on formulation, fill volume, vial type, and equipment performance.
After lyophilization, the dried product is often sealed under vacuum or an inert gas to limit moisture and oxygen exposure. Vials, stoppers, and seals must maintain their barrier throughout shelf life. Storage temperature depends on product sensitivity: some cakes tolerate controlled room temperature, while labile biologics require refrigeration. Humidity is a critical variable because dried cakes are hygroscopic and can absorb water when exposed to air. Handling procedures therefore limit open-vial time and use desiccated environments for sampling.
Quality control for lyophilized materials examines appearance, reconstitution time, residual moisture, and mechanical integrity. An acceptable cake is usually uniform and porous, though appearance alone does not prove stability. Karl Fischer titration is a common method for water content, while differential scanning calorimetry can reveal glass transition events. Stability studies track potency, aggregation, and moisture over time under defined temperature and humidity conditions. Specifications are product-specific and may include sterility and endotoxin tests for sterile preparations.
| Property | Value | Notes |
|---|---|---|
| Common synonyms | Freeze-drying, lyophilisation | Lyophilisation is the British spelling; the process is not simple evaporation. |
| Primary drying pressure | 0.05–0.3 mbar | Pressure must remain below the vapor pressure of ice at the product temperature. |
| Sublimation temperature | Below 0 °C | Ice changes directly to vapor while the product remains frozen. |
| Typical shelf temperature | −40 to −10 °C | Exact setting depends on formulation critical temperature and equipment. |
| Cycle duration | 12–72 hours | Time varies with fill volume, formulation, and dryer performance. |
Lyophilization removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts liquid water into ice and fixes the structure of the sample. After freezing, primary drying lowers pressure so ice changes directly to vapor without passing through a liquid phase. Secondary drying then removes bound water that remains after ice sublimation. The result is a dry, porous solid that often retains its original shape.
The low pressure used during drying allows water vapor to move from the ice surface to a cold condenser. Energy supplied as heat drives sublimation but must stay below the collapse temperature of the frozen matrix. If the product becomes too warm, the frozen structure may soften or melt, reducing pore formation and slowing drying. Formulations often include bulking agents, stabilizers, or buffers to support a rigid cake. The final moisture content depends on formulation, freezing rate, and the length of secondary drying.
Freeze-dried materials are hygroscopic to varying degrees and can take up moisture after drying. Storage therefore often uses sealed glass vials, rubber stoppers, and crimp seals to limit contact with ambient humidity. A desiccant may be included for moisture-sensitive products, although it is not universal. Controlled room temperature is sufficient for many lyophilizates, while others require refrigeration or freezing. Moisture ingress remains a primary cause of cake collapse, chemical degradation, and loss of reconstitution performance.
Quality assessment of a lyophilized product includes cake appearance, residual moisture, reconstitution time, and container closure integrity. A uniform, porous cake suggests that freezing and drying stayed within the formulation's design space. Cracks, shrinkage, meltback, or a glassy film can indicate thermal abuse or a formulation problem. Analysts also test for subvisible particles and sterility when the product requires those specifications. Visual inspection alone cannot confirm biological activity or chemical stability, so it is combined with analytical methods.
The raw materials are different paper pulps. The pulp may be from softwood, hardwood, fiber crops, mineral fibers. For high quality filters, dissolving pulp and mercerised pulp are used. Most filter papers are made using small paper machines. For laboratory filters, the machines may be as small as 50 cm in width. The paper is often crêped to improve porosity. The filter papers may also be treated with reagents or impregnation to get the right properties.
== Personal life == In August 2009, it was reported that Lovett-Murray's home had been raided by police on 3 August. He was charged with possession of a drug of dependency, after the search found a single tablet of ecstasy at his home. However, on 11 December it was reported that the drug charge against him had been dismissed. On 22 May 2013, he was stabbed in a domestic incident by a girl's boyfriend and hospitalised. Lovett-Murray belongs to a sporting family and is the great-grandson of pastor Sir Douglas Nicholls, who played for Fitzroy Football Club. In addition, he is the cousin of former Essendon Football Club player Andrew Lovett.
Wright's invention did not lead to any further developments, and diamorphine became popular only after it was independently re-synthesized 23 years later by chemist Felix Hoffmann. Hoffmann was working at Bayer pharmaceutical company in Elberfeld, Germany, and his supervisor Heinrich Dreser instructed him to acetylate morphine with the objective of producing codeine, a constituent of the opium poppy that is pharmacologically similar to morphine but less potent and less addictive. Instead, the experiment produced an acetylated form of morphine one and a half to two times more potent than morphine itself. Hoffmann synthesized heroin on 21 August 1897, just eleven days after he had synthesized aspirin. The head of Bayer's research department reputedly coined the drug's new name of "heroin", based on the German heroisch which means "heroic, strong" (from the ancient Greek word "heros, ήρως"). Bayer scientists were not the first to make heroin, but their scientists discovered ways to make it, and Bayer led the commercialization of heroin. Bayer marketed diacetylmorphine as an over-the-counter drug under the trademark name Heroin. It was developed chiefly as a morphine substitute for cough suppressants that did not have morphine's addictive side-effects. Morphine at the time was a popular recreational drug, and Bayer wished to find a similar but non-addictive substitute to market. However, contrary to Bayer's advertising as a "non-addictive morphine substitute", heroin would soon have one of the highest rates of addiction among its users.
Sources: en.wikipedia.org
Tendinopathy (tendinitis, U.S. English) is a type of tendon disorder that results in pain, swelling, and impaired function. It most commonly occurs around larger joints, including the shoulder (rotator cuff tendinitis, biceps tendinitis), elbow (tennis elbow, golfer's elbow), wrist, hip, knee (jumper's knee), or ankle (Achilles tendinitis). Causes may include trauma or repetitive activities. Less common causes include infection, arthritis, gout, thyroid disease, diabetes and the use of quinolone antibiotic medicines. Groups at risk include manual laborers, musicians, and sports participants. Diagnosis is typically based on symptoms, examination, and imaging. Typically, little inflammation remains after a few weeks, assuming that the underlying problem is related to weak or disrupted tendon fibrils. Treatment options include rest, NSAIDs, splinting, and physiotherapy. Steroid injections, surgery, or shockwave therapy may be appropriate. About 80% of overuse tendinopathy patients recover completely within six months. Tendinopathy is relatively common. Older people are most commonly affected.
The cornea is the transparent front part of the eyeball which covers the iris, pupil, and anterior chamber. Along with the anterior chamber and lens, the cornea refracts light, accounting for approximately two-thirds of the eye's total optical power. In humans, the refractive power of the cornea is approximately 43 dioptres. The cornea can be reshaped by surgical procedures such as LASIK. While the cornea contributes most of the eye's focusing power, its focus is fixed. Accommodation (the refocusing of light to better view near objects) is accomplished by changing the geometry of the lens. Medical terms related to the cornea often start with the prefix "kerat-" from the Greek word κέρας, horn.
== Biologics, skin substitutes, biomembranes and scaffolds == Advancements in the clinical understanding of wounds and their pathophysiology have commanded significant biomedical innovations in the treatment of acute, chronic, and other types of wounds. Many biologics, skin substitutes, biomembranes and scaffolds have been developed to facilitate wound healing through various mechanisms. This includes a number of products under the trade names such as Epicel, Laserskin, Transcyte, Dermagraft, AlloDerm/Strattice, Biobrane, Integra, Apligraf, OrCel, GraftJacket and PermaDerm.
Sources: en.wikipedia.org
Collagen loss is the gradual decrease of levels of collagen in the body. Collagen is the main structural protein found in the body's various connective tissues (skin, bones, tendons, etc.) where it contributes to much of their strength and elasticity.
There are 19 known americium isotopes and 11 nuclear isomers, having mass numbers 229 through 247. There are two long-lived alpha-emitters; 243Am has a half-life of 7,350 years and is the most stable isotope, and 241Am has a half-life of 432.6 years. The most stable nuclear isomer is 242m1Am – generally called simply 242mAm – with a long half-life of 141 years. The half-lives of other isotopes and isomers are much shorter with a maximum of 50.8 hours for 240Am. As with most other actinides, the isotopes of americium with odd number of neutrons have relatively high fissionability with thermal neutrons and low critical mass. Americium-241 decays to 237Np emitting alpha particles of several different energies, mostly at 5.486 MeV (85.2%) and 5.443 MeV (12.8%). Because the resulting states are metastable, gamma rays are also emitted at discrete energies between 26.3 and 158.5 keV, by far the strongest is at 59.5 keV. The ground state of Americium-242 is a short-lived isotope with a half-life of 16.02 h. It mostly (82.7%) converts by β-decay to 242Cm, but also by electron capture to 242Pu (17.3%). Nearly all (99.55%) of the metastable 242mAm decays by internal conversion to 242Am and the remaining 0.45% by α-decay to 238Np. Americium-243 transforms by α-emission into 239Np.
Addiction psychiatry, addiction medicine Brain injury medicine Child and adolescent psychiatry Consultation-liaison psychiatry Forensic psychiatry Geriatric psychiatry Hospice and palliative medicine Sleep medicine
Sources: en.wikipedia.org
The main change is sublimation, in which ice becomes water vapor without melting into liquid water. This occurs when the chamber pressure is held below the vapor pressure of ice while mild heat is supplied. The result is a dry, porous solid that retains much of its original shape.
Freezing determines ice crystal size, solute distribution, and the pore network left after drying. A slow or fast freezing rate can produce different cake structures and affect reconstitution. It also sets whether the formulation follows an amorphous or crystalline drying path.
It removes most free water during primary drying and part of the bound water during secondary drying. A small residual moisture content often remains and is specified for each product. Complete removal is generally neither practical nor desirable for stability.
No. Freeze-drying removes water but does not reliably kill microorganisms. Sterile lyophilized products are typically prepared aseptically before freezing or are sterilized by a validated method. Microbial control depends on the entire manufacturing process.