If you have been reading about Porous cake and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Last reviewed on 2026-02-12. Where a claim depends on a specific study, the study is described rather than over-claimed.
A typical cycle begins with freezing, sometimes including an annealing step to control ice crystal size. Freezing conditions influence the pore network that later allows vapor escape. During primary drying, shelf temperature and chamber pressure are set so heat enters the product while its temperature stays below the collapse or eutectic point. Secondary drying then raises the shelf temperature to desorb bound water and lower residual moisture. Cycle design depends on formulation, fill volume, container type, and equipment capability.
The physics of lyophilization couples heat transfer, mass transfer, and phase behavior. Sublimation requires a vapor pressure difference between the ice front and the chamber, and the dried layer adds resistance to vapor flow. Amorphous formulations are characterized by a glass transition temperature of the maximally freeze-concentrated solute, often denoted Tg'. Crystalline bulking agents can provide structure, while amorphous excipients stabilize labile components. Open questions remain about spatial heterogeneity, edge effects, and how laboratory cycles scale to production.
Lyophilization is a drying process in which a solvent, usually water, is removed from a frozen material by sublimation under reduced pressure. The material is first solidified, then placed under vacuum so that ice transitions directly to vapor without a bulk liquid phase. This approach suits heat-sensitive substances that would degrade during conventional evaporation. Primary drying removes unbound ice, while secondary drying reduces water that remains adsorbed to the solid matrix. The result is a porous, lightweight solid that can be reconstituted later.
Lyophilization is a dehydration process that removes water from a frozen material by sublimation under low pressure. The material is first frozen so that water becomes ice; then the surrounding pressure is lowered below the vapor pressure of ice. Heat is applied gently so ice changes directly to vapor without passing through a bulk liquid phase. The vapor is collected on a cold condenser, leaving a dry porous matrix. This process differs from simple evaporation because the material remains frozen during the main drying stage.
The process usually has three stages: freezing, primary drying, and secondary drying. Freezing sets the ice crystal structure and can determine pore size in the final cake. Primary drying removes free ice by sublimation at low pressure and low shelf temperature. Secondary drying removes bound water by raising the shelf temperature, although some water may remain as part of the solid. Cycle parameters depend on formulation, fill volume, vial type, and equipment performance.
The physical chemistry of freezing influences whether a formulation forms an amorphous glass or a crystalline solid. Amorphous systems can collapse if product temperature rises above the glass transition temperature of the freeze concentrate. Crystalline systems may show eutectic melting, where ice and solute melt together at a fixed temperature. Formulators add bulking agents, lyoprotectants, and buffers to preserve structure and biological activity. The optimum cycle keeps product temperature below critical thresholds during primary drying while allowing efficient sublimation.
| Property | Value | Notes |
|---|---|---|
| Physical state | Solid, porous cake or powder | Depends on formulation and container |
| Typical storage temperature | 2–25 °C, protected from moisture | Some materials require colder conditions |
| Solubility class | Usually readily soluble after reconstitution | Not an intrinsic chemical property |
| Common analytical method | Karl Fischer titration | Used for residual moisture |
| Common synonyms | Freeze-drying; lyophilisation | Lyophilisation is a spelling variant |
Lyophilization removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts liquid water into ice and fixes the structure of the sample. After freezing, primary drying lowers pressure so ice changes directly to vapor without passing through a liquid phase. Secondary drying then removes bound water that remains after ice sublimation. The result is a dry, porous solid that often retains its original shape.
The low pressure used during drying allows water vapor to move from the ice surface to a cold condenser. Energy supplied as heat drives sublimation but must stay below the collapse temperature of the frozen matrix. If the product becomes too warm, the frozen structure may soften or melt, reducing pore formation and slowing drying. Formulations often include bulking agents, stabilizers, or buffers to support a rigid cake. The final moisture content depends on formulation, freezing rate, and the length of secondary drying.
Freeze-drying is distinct from simple evaporation and from spray drying. Evaporation removes water at temperatures above freezing, while spray drying rapidly dries droplets in a heated gas stream. Lyophilization avoids high temperatures, which can be useful for heat-sensitive materials such as proteins, vaccines, and some foods. The porous cake produced by sublimation dissolves or rehydrates more quickly than a dense dried mass. Not all materials tolerate freezing or the pH shifts that can occur as solutes concentrate during ice formation.
The physics of lyophilization depends on phase boundaries and heat and mass transfer. During primary drying, heat supplied to the product must equal the latent heat of sublimation, while water vapor moves through the drying cake to the condenser. If shelf temperature or pressure is set too high, the ice front can exceed the collapse temperature, causing meltback or pore collapse. If conditions are too cold, drying slows and costs rise. Formulation excipients, vial geometry, and freezing rate alter these limits.
Equipment for lyophilization includes a vacuum chamber, temperature-controlled shelves, a condenser, and a vacuum pump. A refrigeration system cools the shelves and condenser below the product's freezing point. Process monitoring often uses Pirani and capacitance manometers, thermocouples, and resistance sensors. Cycle development balances product quality with time and energy use. Some products are annealed during freezing to improve crystallization of bulking agents. Open questions remain about scaling cycles between laboratory, pilot, and production freeze-dryers.
Lyophilization removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts liquid water into ice and concentrates dissolved solids. Primary drying then lowers chamber pressure so ice changes directly into vapor without passing through a liquid phase. Secondary drying raises the shelf temperature to remove bound water that remains after ice sublimation. The result is a dry, porous structure that can be reconstituted later.
Formulation composition influences whether freeze-drying produces an intact cake or a collapsed mass. Excipients such as sugars and polymers can raise the collapse temperature and provide bulk during drying. The critical temperature for primary drying is often the collapse temperature or the glass transition temperature of the maximally concentrated phase. If the product temperature exceeds this threshold, the frozen matrix may soften and lose structure. Established practice therefore links shelf temperature and chamber pressure to the formulation's thermal properties.
The physics of freeze-drying couples heat transfer, mass transfer, and phase change. Heat supplied through the shelf must reach the sublimation front without melting the ice or degrading the product. Water vapor then travels through the already dried layer and leaves the chamber, where low pressure and cold traps keep it from returning. The dried layer acts as a resistance to vapor flow, so drying rate changes as the front recedes. Open questions remain about how pore structure and formulation heterogeneity affect drying uniformity at larger scales.
=== Toxicity === In 2009, one case of sympathomimetic toxicity was reported in the UK after a person took 0.2 g of mephedrone orally, and after this did not achieve the desired effect, intramuscularly injected 3.8 g mixed with water into his thighs. Shortly afterwards, the user "developed palpitations, blurred tunnel vision, chest pressure and sweating". The patient was treated with 1 mg of lorazepam and the sympathomimetic features decreased and the user was discharged within six hours of arrival. One case of serotonin syndrome has been reported, where the patient was already prescribed fluoxetine and olanzapine, and then took 40 tablets containing mephedrone in one night. He was treated with lorazepam and discharged 15 hours after admission. Both enantiomers of methcathinone, which differs only in the lack of the methyl group on the phenyl ring when compared to mephedrone, have been shown to be toxic to rat dopamine neurons, and the S-enantiomer was also toxic against serotonin neurons. Simon Gibbons and Mire Zloh of the School of Pharmacy, University of London stated, based on the chemical similarities between methcathinone and mephedrone, "it is highly likely that mephedrone will display neurotoxicity". However, Brunt and colleagues stated, "extreme caution" should be used when inferring the toxicity of mephedrone from methcathinone, noting some of the toxicity associated with methcathinone is due to manganese impurities related to its synthesis, rather than the compound itself.
Leukolike vectors are a type of nanoparticles made of nanoporous silicon encapsulated by extracted native leukocyte membranes. These particles were among the first artificial white blood cells to be studied as a proof of concept of using cellular membranes to prolong circulation of nanoparticles throughout the blood. Studies have shown that leukolike vectors have a specific advantage in chemotherapy drug delivery to cancer. This is because leukolike vectors specifically have the potential to bind to tumor endothelium.
A schematic of the optical systems is shown in Figure 1. The variable UV-Vis absorbance detector's optical bench is showing how the flow cell is positioned after the optical system, including the monochromator, which typically has a physical slit and a moving grating, so it is illuminated by a selected wavelength, reaching a photo-diode. The bench of the diode array detector, however, is configured so that the flow cell is positioned before the optical parts, so that the beam containing the entire spectrum is passing through it. The optical parts consist also with a monochromator and a slit, but with a fixed grating, which disperses the light onto a diode array imaging element.
Sources: en.wikipedia.org
==== Original attempt – Gorin ==== In 1974, French film-maker Jean-Pierre Gorin commissioned Dick to write a screenplay based on Ubik. Dick completed the screenplay within a month, but Gorin never filmed it. The screenplay was published as Ubik: The Screenplay in 1985 (ISBN 978-0911169065) and again in 2008 (ISBN 9781596061699). Dick's former wife Tessa claims that the published screenplay "has been heavily edited, and others have added material to the screenplay that Phil wrote", though she suggests that "film producers really ought to take a look at the author's own screenplay before embarking upon their journey of interpretation".
Cannabidiol (CBD) is a phytocannabinoid, one of 113 identified cannabinoids in Cannabis, along with tetrahydrocannabinol (THC), and accounts for up to 40% of the plant's extract. Medically, it is an anticonvulsant used to treat two rare forms of childhood epilepsy. It was discovered in 1940. Clinical research on CBD has included studies related to the treatment of anxiety, addiction, psychosis, movement disorders, and pain, but there is insufficient high-quality evidence that CBD is effective for these conditions. CBD is sold as a herbal dietary supplement and promoted with unproven claims of particular therapeutic effects. Cannabidiol can be taken internally in multiple ways, including by inhaling cannabis smoke or vapor, swallowing it by mouth, and through use of an aerosol spray inside the cheek. It may be supplied as CBD oil containing only CBD as the active ingredient (excluding THC or terpenes), CBD-dominant hemp extract oil, capsules, dried cannabis, or prescription liquid solution. CBD does not have the same psychoactivity as THC, and can modulate the psychoactive effects of THC on the body if both are present. Conversion of CBD to THC can occur when CBD is heated to temperatures between 250–300 °C, potentially leading to its partial transformation into THC. In the United States, the cannabidiol drug Epidiolex was approved by the Food and Drug Administration (FDA) in 2018, for the treatment of two seizure disorders.
In 2023, Vasquez introduced bipartisan legislation aimed at addressing the teacher shortage in Indian Country. The bill proposed providing federal pension benefits to educators working in tribal schools, seeking to improve teacher retention and support Native American students. Vasquez voted that year in favor of requiring healthcare workers to receive the COVID-19 vaccine. The following day, he opposed a resolution to end the COVID-19 national emergency. On women's health, he has supported abortion rights and advocated for codifying Roe v. Wade into federal law. In 2024, Vasquez voted in favor of the Protecting Americans from Foreign Adversary Controlled Applications Act, sometimes called the TikTok ban, which sought to address concerns over data security and foreign influence. On July 19, he called for President Joe Biden to withdraw from the 2024 presidential election, citing concerns over his age and ability to campaign effectively. In December 2025, NBC News and The New York Times reported that Vasquez had voted against a bill to reopen the federal government and then touted the money the bill delivered to his district. After the federal government was reopened, primarily with Republican votes, after a 43-day shutdown, Vasquez was among Democrats who "claimed credit for some provisions in the bill." Former Speaker Nancy Pelosi coined the term "vote no and take the dough" when Republicans took credit for money brought to their districts under bills they opposed.
Sources: en.wikipedia.org
Freezing only converts liquid to solid. Lyophilization adds vacuum and controlled warming so frozen solvent sublimes, leaving a dry porous solid. The two steps are related but not interchangeable.
Reduced pressure keeps the solvent below its triple point, allowing ice to become vapor without melting. Vacuum also helps remove water vapor from the product chamber. The exact pressure is chosen with the formulation and equipment.
Residual moisture is water that remains in the dried solid after secondary drying. It is often measured by Karl Fischer titration, near-infrared spectroscopy, or thermogravimetry. Acceptable levels depend on the material and its stability profile.
The main change is sublimation, in which ice becomes water vapor without melting into liquid water. This occurs when the chamber pressure is held below the vapor pressure of ice while mild heat is supplied. The result is a dry, porous solid that retains much of its original shape.